Messages

I have configured SIP endpoints via Config Professional as well as SCCP on my 2901 voice. Not sure if your phones are strictly SIP or some other consideration is required, though. Your phones have Spark OS which I've not seen, but if it's just SIP, then you can set up a basic SIP endpoint via CCP like I done with my android phones. Was flaky, but still done it.

Could you send to me user guide configure SIP endpoint via Config Professional? Coz I only find configure SCCP via Config Professional. I use Cisco IP 7811, 7861 and 8831. They run with SIP OS follow specification.

lekimcang -- these phones use the Cisco Spark OS.
I recommend:
1. check feature compatibility with your equipment
2. Give Cisco Configuration Professional a try if you've not tried already. It's a GUI for the CUCME so will help you by showing you what options are available to you.
3. it could be a bug

Cisco Configure Professional don't support configure for CME SIP Phone. It support for CME SCCP. If you want to use it, you must upload source GUI of CME to flash. I tried this way.

Hi Dieselboy

I did it. Follow command line :
1. Configure Conference:

voice register template 1
  transfer-attended enable
  transfer-blind enable
  softkey connected Confrn Endcall Hold Trnsfer
  softkey idle Cfwdall Newcall Redial
  softkey hold Newcall Resume
  softkey seized Cfwdall Endcall Redial

voice register pool 1
  template 1
  keep-conference

2. Configure Speed-dial
voice register template 1
  button-layout 1 line
  button-layout 2-7 speed-dial
voice register pool 1
  template 1
  speed-dial 1 [number dial]
  apply-configure

3. Show password admin setting of Phone
router#more flash:its/SEPD[MAC Phone].cnf.xml | inlcude phonePassword

Hope everybody can follow this guide to configure CME. This version CME is 11.5.

yes, I tried same model, but it still don't make the conference. Maybe have a different way is configuration like :

Voice register template 1
transfer-attended
transfer-blind

this way follow guide of Cisco. Hope it will works.

It is 7811, I will try 7861 and 7811. It same

Hi Deanwebb

Unfortunately, It doesn't work. I tried 2 way below :

- Phone A is creator. Phone A call to Phone B - success, cont Phone A call to Phone C by conf soft key - success. Status on Phone A is 1 pause 1 start. When click conf soft key, don't happen everything

- Phone B is creator. Phone A call to Phone B - success, cont Phone B call to Phone C by conf soft key - success. Status on Phone B is 1 pause 1 start. When click conf soft key, don't happen everything.

Thanks Deanwebb

I will try again. Hope it work. According to document, configuration for CUCM. I will try on CME. I will feedback if successful.

I need different configure or help me find errors in my configuration. I configured speed-dial button successfully. So now I have only 1 problem :

       - Can not use conference feature on IP Phone 7811 and 7861 by adhoc.

That new configuration

Dear all

I have some problem with IP Phone 7861, 7811 :

    - I can not use conference feature on IP Phone 7811 and 7861 by adhoc.

    - I configure speed-dial button on CME, but on IP Phone 7861 don't use button to make call

I configure CME with SIP protocol. About configure Speed-dial button like :

voice register template  1
button-layout 1 line
button-layout 2-7 speed-dial

voice register pool  17
busy-trigger-per-button 6
id mac D42C.4485.5BEA
type 7861
number 1 dn 400
template 1
presence call-list
dtmf-relay sip-notify
username 1000 password 1000
codec g711ulaw
speed-dial 1 +1010 label "Diep"