SimonV's Blog-IPv6 on Juniper SRX – Prefix Delegation & DHCPv6

Started by SimonV, September 09, 2022, 06:15:00 AM

Previous topic - Next topic

SimonV

IPv6 on Juniper SRX – Prefix Delegation & DHCPv6

I’m currently setting up IPv6 in my own office so I thought it would be worth documenting the configuration I’m adding on my Juniper equipment to make it all work. I have an internet subscription with a static IPv4 address and also included with it is a /48 static IPv6 prefix. There are two ways … Continue reading IPv6 on Juniper SRX – Prefix Delegation & DHCPv6

I’m currently setting up IPv6 in my own office so I thought it would be worth documenting the configuration I’m adding on my Juniper equipment to make it all work.


I have an internet subscription with a static IPv4 address and also included with it is a /48 static IPv6 prefix. There are two ways I can set it up: static configuration or “semi-automatic” by using Prefix Delegation. This article discusses the latter and in my next post I will document the static configuration, as that’s what I will ultimately be using.


First Things First – Enabling IPv6 Forwarding


Before you can start using IPv6 on the SRX, the device needs to be explicitly configured to forward V6 traffic. This because, by default, the forwarding mode for IPv6 is set to drop. You can verify this on the command line – as shown below, the default forwarding mode for Inet6 traffic is drop:


np@NP-FW01> show security flow status
  Flow forwarding mode:
    Inet forwarding mode: flow based
    Inet6 forwarding mode: drop
    MPLS forwarding mode: drop
    ISO forwarding mode: drop
  Flow trace status
    Flow tracing status: off
  Flow session distribution
    Distribution mode: RR-based
  Flow ipsec performance acceleration: off
  Flow packet ordering
    Ordering mode: Hardware

To activate it, you must change the forwarding mode. There are three modes to choose from: drop (default), flow-based and packet-based.


[edit]
np@NP-FW01# set security forwarding-options family inet6 mode ?
Possible completions:
  drop                 Disable forwarding
  flow-based           Enable flow-based forwarding
  packet-based         Enable packet-based forwarding

I’m using the SRX as a stateful firewall, so I’ll configure flow-based and commit. JunOS will warn you that the change is active only after a device reboot, so I’ll reboot the SRX and continue below.


[edit]
np@NP-FW01# set security forwarding-options family inet6 mode flow-based
[edit]
np@NP-FW01# show | compare
[edit security]
+   forwarding-options {
+       family {
+           inet6 {
+               mode flow-based;
+           }
+       }
+   }
[edit]
np@NP-FW01# commit
warning: You have enabled/disabled inet6 flow.
You must reboot the system for your change to take effect.
If you have deployed a cluster, be sure to reboot all nodes.
commit complete

After the reboot, the forwarding mode is set to flow based and we can start implementing IPv6.


np@NP-FW01> show security flow status
  Flow forwarding mode:
    Inet forwarding mode: flow based
    Inet6 forwarding mode: flow based
    MPLS forwarding mode: drop
    ISO forwarding mode: drop
  Flow trace status
    Flow tracing status: off
  Flow session distribution
    Distribution mode: RR-based
  Flow ipsec performance acceleration: off
  Flow packet ordering
    Ordering mode: Hardware

Configuring IPv6 with Prefix Delegation


Prefix delegation is a simple method to automate the assignment of IPv6 prefixes on subscriber equipment. The CPE (in my case the SRX) informs the upstream router, called the Broadband Network Gateway (BNG) that it wants to use Prefix Delegation. The BNG retrieves the prefix for the subscriber and announces the /48 back to the CPE, after which both sides confirm the prefix allocation. The CPE will then automatically divide the /48 into smaller /64 subnets on the LAN interfaces it has configured for PD Router Advertisements.


If you want to find out exactly how it works, you can find more information in RFC3633


First, we configure the outside interface, pp0.0 in my case. Notice that we are configuring this under family inet6.


The DHCPv6 client is activated on the outside, ISP-facing interface. Some PD-specific configuration is added and we will request the DNS server addresses from the provider.


[edit interfaces pp0 unit 0 family inet6]
np@NP-FW01# show
dhcpv6-client {
    client-type statefull;
    client-ia-type ia-pd;
    rapid-commit;
    client-identifier duid-type duid-ll;
    req-option dns-server;
    retransmission-attempt 0;
}

The LAN interface, in my case ae0.311, on which I will further delegate the prefix, is specified. Showing this separately as it’s important not to miss this one! 🙂


[edit interfaces pp0 unit 0 family inet6]
np@NP-FW01# set dhcpv6-client update-router-advertisement interface ae0.311

The last step is to allow DHCPv6 packets on the security zone inbound traffic. Could be that you need to add it under the interface, if you specified it further down on that level.


[edit security zones security-zone edge-untrust]
np@NP-FW01# set host-inbound-traffic system-services dhcpv6

If you want to use this on the LAN segment, you will also need to enable DHCPv6 on that security zone and interface. I’m using a guest VLAN for testing so I’ll enable it there.


[edit]
np@NP-FW01# set security zones security-zone edge-guest host-inbound-traffic system-services dhcpv6

After a commit, we see that interface ae0.311 now has a public IPv6 address with a /64 mask.


np@NP-FW01> show interfaces terse
Interface               Admin Link Proto    Local                 Remote

ae0.311                 up    up   inet     192.168.200.1/24
                                   inet6    2a02:1234:420a:1::1/64
                                            fe80::aad0:e501:37d3:2a80/64
...

Notice that the SRX has taken the original /48 prefix and automatically derived a /64 subnet from it for interface ae0.311: 2a02:1234:420a:1::1/64 .


Note – real prefix modified for obvious reasons 🙂


Before we can test reachability, we will need to configure the default route via pp0.0. I’m using routing-instances (VRFs) so I will add it on my external edge instance.


[edit routing-instances VRF-Edge routing-options]
np@NP-FW01# show
rib VRF-Edge.inet6.0 {
    static {
        route ::/0 next-hop pp0.0;
    }
}

With the default route in place, we should be able to ping a public v6 address from this VRF. Below, we are pinging Google DNS, from the interface with Prefix Delegation.


np@NP-FW01> ping 2001:4860:4860::8888 routing-instance VRF-Edge rapid count 10 source 2a02:1234:420a:1::1
PING6(56=40+8+8 bytes) 2a02:1234:420a:1::1 --> 2001:4860:4860::8888
!!!!!!!!!!
--- 2001:4860:4860::8888 ping6 statistics ---
10 packets transmitted, 10 packets received, 0% packet loss
round-trip min/avg/max/std-dev = 31.811/32.841/35.861/1.163 ms

Success! This shows that IPv6-PD is working as expected and that the delegated prefix is globally reachable.


After connecting a test machine inside the VLAN, we can confirm that the router advertisements are working as expected. The client has taken the /64 prefix and assigned itself an EUI-64 address.


Ethernet adapter Ethernet:

   Connection-specific DNS Suffix  . : netprobe.guest
   Description . . . . . . . . . . . : Intel(R) Ethernet Connection (4) I219-V
   Physical Address. . . . . . . . . : C8-5B-76-BC-04-6E
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv6 Address. . . . . . . . . . . : 2a02:1234:420a:1:103f:efd8:f2f7:d0cf(Preferred)
   Temporary IPv6 Address. . . . . . : 2a02:1234:420a:1:293c:fd60:c216:8123(Preferred)
   Link-local IPv6 Address . . . . . : fe80::103f:efd8:f2f7:d0cf%14(Preferred)
   IPv4 Address. . . . . . . . . . . : 192.168.200.13(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : zondag 12 november 2017 15:23:41
   Lease Expires . . . . . . . . . . : maandag 13 november 2017 15:26:16
   Default Gateway . . . . . . . . . : fe80::aad0:e501:37d3:2a80%14
                                       192.168.200.1
   DHCP Server . . . . . . . . . . . : 192.168.200.1
   DHCPv6 IAID . . . . . . . . . . . : 63462262
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-20-35-58-1B-C8-5B-76-BC-04-6E
   DNS Servers . . . . . . . . . . . : 208.67.220.123
                                       208.67.222.123
   NetBIOS over Tcpip. . . . . . . . : Enabled

Now, this part seems to be working fine, but you may notice that the client has not received any IPv6 name servers.

This is because the client uses SLAAC to configure its v6 address based on the Router Advertisements, but it still relies on DHCPv6 to receive any special information such as DNS servers.


To make this work, we need to add a few more bits of configuration to use the SRX as a a DHCPv6 server.


Handing out DNS servers via DHCPv6


First, configure the DHCPv6 pool with the prefix and the DNS server you want to hand out. I’m using Google DNS here.


np@NP-FW01# show routing-instances VRF-Edge access address-assignment
pool vlan311-dhcpv6 {
    family inet6 {
        prefix 2a02:1234:420a:1::/64;
        dhcp-attributes {
            dns-server {
                2001:4860:4860::8888;
                2001:4860:4860::8844;
            }
        }
    }
}

Next, configure the internal DHCPv6 server under system services, referring to the pool you just created – add it under routing-instances if required!


np@NP-FW01# show routing-instances VRF-Edge system services dhcp-local-server
dhcpv6 {
    overrides {
        interface-client-limit 100;
        process-inform {
            pool vlan311-dhcpv6;
        }
    }
    group ipv6 {
        interface ae0.311;
    }
}
group group-vlan311 {
    interface ae0.311;
}

Activate Router Advertisements for your outside interface. It doesn’t seem to work for me without this.


[edit]
np@NP-FW01# show protocols router-advertisement
interface pp0.0;

The following bit controls the Router Advertisements on the delegated interface and activates the O-Flag (Other Information) on the RAs.


[edit interfaces pp0 unit 0 family inet6 dhcpv6-client update-router-advertisement interface ae0.311]
+         other-stateful-configuration;
+         max-advertisement-interval 6;
+         min-advertisement-interval 3;

After adding this configuration, we see the client has now successfully picked up the new DNS settings.


Ethernet adapter Ethernet:

   Connection-specific DNS Suffix  . : netprobe.guest
   Description . . . . . . . . . . . : Intel(R) Ethernet Connection (4) I219-V
   Physical Address. . . . . . . . . : C8-5B-76-BC-04-6E
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv6 Address. . . . . . . . . . . : 2a02:1234:420a:1:103f:efd8:f2f7:d0cf(Preferred)
   Temporary IPv6 Address. . . . . . : 2a02:1234:420a:1:488c:f549:1e67:254c(Preferred)
   Link-local IPv6 Address . . . . . : fe80::103f:efd8:f2f7:d0cf%14(Preferred)
   IPv4 Address. . . . . . . . . . . : 192.168.200.13(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : zondag 12 november 2017 15:23:41
   Lease Expires . . . . . . . . . . : maandag 13 november 2017 17:08:57
   Default Gateway . . . . . . . . . : fe80::aad0:e501:37d3:2a80%14
                                       192.168.200.1
   DHCP Server . . . . . . . . . . . : 192.168.200.1
   DHCPv6 IAID . . . . . . . . . . . : 63462262
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-20-35-58-1B-C8-5B-76-BC-04-6E
   DNS Servers . . . . . . . . . . . : 2001:4860:4860::8888
                                       2001:4860:4860::8844
                                       208.67.220.123
                                       208.67.222.123
   NetBIOS over Tcpip. . . . . . . . : Enabled

After adding a security policy that allows IPv6 traffic, the client can succesfully communicate over IPv6.


C:\Users\Simon>nslookup - 2001:4860:4860::8888
Default Server:  google-public-dns-a.google.com
Address:  2001:4860:4860::8888

> google.com
Server:  google-public-dns-a.google.com
Address:  2001:4860:4860::8888

Non-authoritative answer:
Name:    google.com
Addresses:  2a00:1450:400e:80b::200e
          172.217.20.110

C:\Users\Simon>ping -6 www.google.com

Pinging www.google.com [2a00:1450:400e:806::2004] with 32 bytes of data:
Reply from 2a00:1450:400e:806::2004: time=30ms
Reply from 2a00:1450:400e:806::2004: time=31ms
Reply from 2a00:1450:400e:806::2004: time=31ms
Reply from 2a00:1450:400e:806::2004: time=30ms

Ping statistics for 2a00:1450:400e:806::2004:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 30ms, Maximum = 31ms, Average = 30ms

Verification Commands


Checking which prefix was allocated to you by the ISP – don’t forget to specify the routing-instance if you are using them.


np@NP-FW01> show dhcpv6 client binding routing-instance VRF-Edge

IP/prefix                       Expires     State      ClientType    Interface       Client DUID
2a02:1234:420a::/48              2590728     BOUND      STATEFUL      pp0.0           LL0x29-a8:d0:e5:d3:2a:47

You can renew the prefix lease this way:


np@NP-FW01> request dhcpv6 client renew routing-instance VRF-Edge interface pp0.0

Displaying the IPv6 neighbours – this is similar to your ARP table in IPv4.


np@NP-FW01> show ipv6 neighbors
IPv6 Address                 Linklayer Address  State       Exp Rtr Secure Interface
2a02:1234:420a:1:488c:f549:1e67:254c
                             c8:5b:76:bc:04:6e  stale       1017 no no      ae0.311
fe80::103f:efd8:f2f7:d0cf    c8:5b:76:bc:04:6e  stale       363 no  no      ae0.311

Statistics for the DHCPv6 server:


np@NP-FW01> show dhcpv6 server statistics routing-instance VRF-Edge
Dhcpv6 Packets dropped:
    Total               0

Messages received:
    DHCPV6_DECLINE             1
    DHCPV6_SOLICIT             6
    DHCPV6_INFORMATION_REQUEST 60
    DHCPV6_RELEASE             0
    DHCPV6_REQUEST             3
    DHCPV6_CONFIRM             0
    DHCPV6_RENEW               0
    DHCPV6_REBIND              0
    DHCPV6_RELAY_FORW          0
    DHCPV6_RELAY_REPL          0

Messages sent:
    DHCPV6_ADVERTISE           4
    DHCPV6_REPLY               8
    DHCPV6_RECONFIGURE         0
    DHCPV6_RELAY_REPL          0

Now, if I was running a fairly simple network with just a few subnets, I would be using Prefix Delegation but I also have a couple of L3 devices behind this firewall. Extending PD all the way down would make it overly complex, so I’ll go for static configuration with OSPFv3 in the next article.


Please let me know in the comments if this configuration did not work for you!


Source: IPv6 on Juniper SRX – Prefix Delegation & DHCPv6